What're your opinions on A Step-by-Step Guide to Installing a Bathtub?

Installing a tub isn't specifically rocket science, however it does require solid plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is also a reasonably tough task. If the old tub is readily accessible, the job can relocate easily; if you need to open a wall surface to eliminate the old tub and also position the new bathtub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly need an assistant to leave the old tub and embeded in the brand-new one. See to it you have certified on your own for the task and are comfortable attempting it. As opposed to hiring a professional to take control of a halfway-completed project, it is far better to take into consideration utilizing one prior to you start. Opportunities are you may require an expert plumber to make tube connections.
This post will certainly aid you install a new bathtub in your shower room if you have actually currently acquired a brand-new tub and also do not require to alter the arrangement of your previous water pipelines.
Your devices as well as product checklist must comprise the following:
- New Tub
- Hammer
- Pipe Wrenches
- Prybar
- Safety Glasses
- Level
- Pliers
- Flexible Wrench
- Putty Knife
- Screwdriver
- Cold Knife
- Tape Measure
- Pipe Caps
Getting ready for the Setup
Firstly, the supporting framework provided with the bathroom must be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to prevent strain on the bathtub.
Fit the adaptable tap adapters to the bottom of both faucets making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you utilize all of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its last position.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be rather bothersome due to the restricted gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the remaining water that will come from the pipelines. When the supply pipelines have actually been eliminated, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from turning throughout this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old securing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Using both wooden boards under its feet, put the tub in the required placement. The wood boards are helpful in evenly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four small points.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level and also changing the feet on the tub till the level checks out level.
To mount taps, fit all-time low of the outermost versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the other tap.
Activate the water system as well as check all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub as well as likewise inspect the overflow electrical outlet and also the typical electrical outlet for leakages.
Finally, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and securing around the bathtub must wait up until the tub has been utilized at least when as this will certainly settle it right into its last placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making sure that the washers are in area in between the faucet as well as the sink. Safeguard the tap in position with the supplier supplied backnut. As soon as the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former type ought to be linked to the tap ends first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath meets the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture an inflexible seal, creating the water to penetrate the wall between the bath and the tiling, bring about difficulties with moisture and also possible leaks to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures and also installations. They are offered in tubes as well as cartridges, and can sealing spaces up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of drenched newspaper or soft rope. Remember to always fill up the tub with water prior to securing, to enable the activity experienced when the bathtub is in usage. The sealer can break fairly early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

Do you enjoy reading about A Step-by-Step Guide to Installing a Bathtub? Make feedback directly below. We'd be glad to listen to your thinking about this blog. We are looking forward that you come back again in the near future. Enjoyed reading our piece of writing? Please share it. Let other people locate it. We thank you for reading our article about Installing A Bathtub.
24/7 plumbers for emergencies.
Comments on “Getting Familiar with Plumbing: Your Starting Point for Bathtub Installation”